FAQ: Carbon Wheels, Fitment, Shipping and Warranty

Straight answers to the questions we get most, grouped by what you are trying to decide. Every answer links to the page or policy that has the detail. If your question is about a specific build — axle spacing, tyre clearance on your frame — the fitment guide is the fastest route.

Buying and compatibility

Which Bola wheelset fits my bike?

Four checks decide it: brake type (rim or disc), axle standard (quick-release or thru-axle), frame and tyre clearance, and the tyre width you actually ride. The wheel fitment guide walks through 700c, 650b and 29er with the measurements to take before ordering.

Are 700c and 29er the same size?

Yes. Both use a 622 mm bead seat diameter, so a 29er rim and a 700c rim are the same circle. The difference is application: 29er is the mountain-bike label for that diameter, and gravel and road wheels use the 700c name. Tyre clearance on your frame, not the label, decides what fits.

Will 700c wheels fit my mountain or touring bike?

Only if the frame and fork clear the tyre you plan to run and the brake and axle match. Many 29er MTB frames are 622 mm compatible but run Boost spacing, while touring frames are often quick-release 100/130 mm. Check the fitment guide before ordering; we can confirm a specific model if you send your frame spec.

Do you make both disc-brake and rim-brake wheels?

Yes, but they are separate builds — a rim-brake wheel cannot take a disc rotor and a disc wheel has no brake track. Rim-brake builds are quick-release 100/130 mm; disc builds use thru-axle 12 × 100 / 142 mm unless a model says otherwise.

Can I convert a rim-brake wheel to disc?

No. The hub, spoke count and rim layup differ between the two. Order the disc-brake build for a disc frame; there is no conversion kit that makes a rim-brake wheel safe on a disc bike.

Which freehub ships with the wheelset?

Shimano HG is fitted as standard, so HG cassettes mount straight on. If you run SRAM XD or XDR, note it at checkout and we build the matching driver; DT Swiss 350-based hubs can also be swapped later.

Will the wheels work with 12-speed groupsets?

Yes, provided the driver matches your cassette. Shimano 12-speed road uses HG, SRAM 12-speed road uses XDR, and MTB 12-speed is usually Micro Spline or XD. Tell us the groupset at checkout and the correct freehub is fitted before shipping.

What axle standards do you cover?

Quick-release 100/130 mm on rim-brake wheels; thru-axle 12 × 100 front and 12 × 142 rear on disc road and gravel; Boost 15 × 110 / 12 × 148 on MTB builds, with some models offered in both. Confirm the exact standard on the product page before you order.

What is the maximum system weight?

120 kg for the 28/30/32 mm internal-width builds with hookless-rated tubeless tyres — that includes rider, kit and luggage. Lighter road and gravel builds have their own rating on the product page; if you are near the limit, ask us before ordering rather than after.

What is in the box?

Each wheelset ships tubeless-ready with rim tape and valves fitted, plus spare spokes. Sealant is not included because it has a shelf life and is easier to buy locally. Tubular builds ship with valves and spare spokes, and you supply the tubular cement.

Do I need to buy tape or valves separately?

No. Rim tape and valves are already fitted on tubeless-ready builds, and spare spokes are packed in the box. You only add sealant. On bare rims, tape is not included — those are sold for custom builds.

Can I buy a bare rim instead of a complete wheel?

Yes. Bare rim listings ship the rim only — no hub, spokes, nipples or tape — so you can lace it to your own hub or hand it to a wheel builder. We can also quote a built wheel if you would rather not build it yourself.

Can you drill the spoke holes to my pattern?

Yes. As an OEM rim supplier we custom-drill spoke holes to your chosen pattern and hole count. Give us the build spec when you order; for rims you lace yourself, confirm the drilling and brake rating before shipping.

Which tyre widths fit which internal rim width?

Rough guide from our current range: 18–21 mm beds suit 25–28c; 23–25 mm beds suit 28–45c; 26–28 mm beds suit 30–40c road and gravel; 30–35 mm beds suit 40–50c gravel; 27–34 mm MTB beds suit 2.1–2.6". The rim width guide has the full table.

Is 35mm wide enough for gravel?

Depth and width are different numbers. The 35G line is 35 mm deep with a 25 or 30 mm internal bed, and riders run 40c to 50c tyres on it. What limits gravel fit is the internal width and your frame clearance, not the rim depth.

Can I run a 28c tyre on a 30mm internal gravel rim?

It will physically mount, but the casing is under-supported and the rim is designed for 40c and wider. For mixed road and gravel use, choose a 25 mm internal rim and run 32–40c, or keep a dedicated road wheelset.

Can I order a front wheel on its own?

Yes. Three-spoke and disc front wheels are listed individually, and a matching rear or a pair can be ordered separately. If you are building a time-trial set, tell us the front depth so the rear is matched for stability.

Do you ship to my country?

We ship internationally with standard, express and sea freight. Free standard shipping applies to orders over USD 300 to most of Europe, North America, Australia and Southeast Asia; remote areas and some destinations carry a surcharge. Full detail is in the shipping policy.

How many inches is a 700c wheel?

The rim is 622 mm at the bead seat, and the overall diameter depends on the tyre: roughly 26.5–27 inches with a 25c road tyre, and 29 inches with a 2.1" MTB tyre — which is where the 29er name comes from. 650b is 584 mm, and 27.5" is its mountain-bike label.

What are the pros and cons of carbon wheels?

Pros: less weight at the rim, higher lateral stiffness, and aero shaping that alloy cannot match. Cons: higher cost, a rim that fails by cracking rather than bending, and brake-track wear on rim-brake models. For most riders the aero and weight gains outweigh the cost; for heavy-duty touring, alloy still has a case.

What is the 105% rule in wheel design?

It is the industry rule of thumb we design to: the rim's external width should be at least 105% of the tyre's measured width, so the tyre does not bulge wider than the rim and disturb the airflow. It is why a 25 mm internal rim is paired with 28–30c tyres rather than 34c.

What should I avoid when buying carbon rims?

A listing with no internal width, no spoke tension figure and no warranty term. Avoid hookless rims sold without an ETRTO tyre recommendation, rims with no impact or weight rating, and any seller who cannot say where the rim is made. Those gaps show up as bead failure or cracking later.

Are carbon wheels good for bikepacking?

Yes within limits. Our 28/30/32 mm builds carry a 120 kg system weight including luggage, and 40–50c tyres on a 25–30 mm internal rim handle loaded gravel and fire roads. Choose hooked rims if you want the option of tubes in remote areas, and carry spare spokes.

What internal width is best for 40mm gravel tyres?

25 mm internal. It gives the 40c casing a round profile without over-stretching it, and it still supports 45–50c if you size up. A 30 mm bed is the better choice if you ride 45c and wider most of the time; below 23 mm the tyre balloons and feels vague in loose corners.

What makes a gravel wheelset durable?

Four things: an internal width matched to your tyre, 24–28 spokes rather than a weight-weenie count, a reinforced bead and spoke bed that passes impact testing, and hubs you can service with standard tools. Depth matters far less than those four on gravel.

Technical specs

How much do Bola carbon wheels weigh?

Rider-reported weights cluster between 1,170 g and 1,270 g for 45 mm road pairs, around 1,220 g for a 35 mm gravel pair, and 1,000 g for the 180 mm tri-spoke front. Exact weight depends on hub, spoke type and rim version, and is listed on each product page — treat review numbers as checks, not catalogue specs.

Which rim depths do you offer?

From 35 mm gravel and 38–40 mm all-round road through 45, 50 and 60 mm aero, up to 88 mm and 180 mm for time trial and track. Depth is a handling choice as much as a speed choice; the wheel choice guide compares 40, 50 and 60 mm directly.

What is the difference between internal and external width?

Internal width is the distance between the bead seats and sets the tyre's shape and volume. External width is the widest point of the rim and drives airflow. A 25 mm internal rim is typically about 30–32 mm externally; the rim width guide explains how each affects ride quality.

Hooked or hookless — which should I buy?

Hooked rims clamp the tyre bead and accept standard clinchers with tubes. Hookless rims are simpler and lighter but require ETRTO hookless-rated tubeless tyres and a 72.5 PSI cap on 28c and wider. If you switch between clincher and tubeless, choose hooked.

What is the pressure limit on hookless rims?

Per ETRTO, tubeless tyres 28c and wider on hookless rims must not exceed 72.5 PSI (5.0 bar). Above that the bead can separate. Heavier riders should size up the tyre rather than raise pressure.

Can I use any tubeless tyre on a hookless rim?

No. Only tyres the manufacturer lists as hookless-compatible. ETRTO-rated hookless tyres have a bead designed for the lower seating force; a non-rated tyre may seat and then fail under load. Check the tyre sidewall before mounting.

Can I run inner tubes in hookless rims?

ETRTO does not permit tubes in hookless road rims; hookless is a tubeless-only system. If you want the option of tubes — for a spare, or for clincher tyres — order a hooked rim instead.

Why are carbon wheels so expensive?

Labour and tooling, not material alone. A rim is laid up and drilled by hand, then built into a wheel that has to hold 100 kg at 60 km/h. Where that labour happens and how many intermediaries sit between factory and rider is what separates a $468 wheelset from a $2,000 one.

Why are carbon wheels so loud?

The noise is the freehub ratchet, not the rim. Bola builds use 36T or 54T ratchets; riders describe the sound as moderate rather than loud. A deeper rim adds wind and rolling noise at speed, which is often mistaken for hub noise.

How much faster are carbon wheels?

Depth buys aero gains that grow with speed; weight buys acceleration on climbs and when sprinting. Neither is a fixed watt number — it depends on your speed, position and the rim you compare against. Expect "easier to hold speed and quicker to accelerate" rather than a dramatic jump.

How many watts do carbon wheels save?

Any single figure is a marketing simplification. Savings scale with speed, yaw angle and depth, and a shallow climbing rim can be slower than a 50 mm rim on a flat course. Compare like-for-like depths and read the depth comparison before deciding.

What spoke tension should the wheels be built to?

Drive-side and disc-side maximum is 130–140 kgf, with the non-drive side matched to it. Spoke holes are locally reinforced inside the layup, so the rim tolerates that tension without pull-through. Build to the upper half of the range for disc brakes.

Will carbon spokes snap suddenly?

Carbon spokes run about 3,800 N tensile strength, above the roughly 3,000 N of top steel spokes, with about 30% more lateral stiffness. They fail progressively under overload rather than shattering, and spare spokes ship in the box.

Can a broken carbon spoke be replaced at a local shop?

Yes on our two-piece mechanical spokes — they are not bonded into the rim, so a shop can swap one without returning the wheel. Spare spokes ship free with the wheelset. One-piece monocoque designs are the exception and need factory replacement.

Which hubs do you use, and what is the engagement?

DT Swiss 350 and 240 hubs depending on the build, with 36T star ratchets as standard — about 10 degrees of engagement — and 54T available on some models for faster pick-up. All are serviceable with standard DT tools and spares.

Are the bearings durable in rain?

Bearings use dual-lip labyrinth seals, so wet riding needs no special disassembly. Plan a grease top-up around every 5,000 km, sooner if you ride in persistent rain or through water crossings. Ceramic bearings follow the same service interval.

Does the wave profile really reduce crosswind torque?

The wave-profile outer width breaks lateral vortices at 10–15 degrees of yaw and cuts steering torque by roughly 25% against a straight profile of the same depth. It does not make a 60 mm rim as calm as a 35 mm rim — it narrows the gap.

What tyre pressure should I run?

Start from the internal width: 21–25 mm beds, 60–90 PSI depending on tyre and rider weight; 28–32 mm gravel beds, 30–45 PSI on 40–50c; MTB 27–34 mm beds, 20–30 PSI. Then adjust for weight and surface — the pressure guide has a calculator.

What is the impact rating of the rims?

The bead area carries a thickened impact layer, and impact testing passes over 60 J — above the 30 J ISO baseline — on the MTB and gravel builds where that test applies. Road rims are not rated for rock strikes, so treat kerbs and potholes as the limit.

How is rim width measured?

Internal width is measured between the two bead seats with a caliper, tape included, and it sets the tyre's shape. External width is the widest point of the rim including the sidewall bulge. A rim listed as 25 mm internal is typically 30–32 mm external — never compare one number against the other.

Which rim depth is right for me?

35–40 mm for all-round riding and climbing, 45–50 mm for fast group rides and rolling terrain, 60 mm and deeper for flat courses and time trial, 88–180 mm for track and triathlon. If you ride in strong crosswinds, stay at 40–45 mm or choose the wave profile.

Are hookless rims safe?

Yes when the system is used as specified: an ETRTO hookless-rated tubeless tyre, seated properly, at or below 72.5 PSI for 28c and wider. Hookless is a design choice that removes the hook to save weight and simplify moulding — not a shortcut, and not a scam.

How strong are carbon wheels?

MTB and gravel rims pass impact testing above 60 J, twice the 30 J ISO baseline, with locally reinforced spoke holes and bead areas. Complete wheels carry a 120 kg system limit, and carbon spokes hold about 3,800 N. Strength comes from layup design, not from adding material everywhere.

How are carbon wheels made?

Pre-impregnated carbon sheets are cut, laid into a mould in a 0/45/90 pattern, cured under heat and pressure, then drilled, finished and built by hand. The layup and the drilling are where quality separates brands — which is why we offer the same process to OEM customers.

Does rolling resistance matter more than wheel weight?

For steady speed, tyre choice and pressure dominate rolling resistance, and rim depth dominates aero above roughly 25 km/h. Wheel weight matters most when accelerating and climbing. A fast tyre on a mid-depth rim beats a light rim on a slow tyre.

Can any tyre run tubeless?

No. The casing needs a tubeless-ready bead; a standard clincher converted with sealant is unreliable at road pressure and unsafe on hookless rims. Use a TLR or hookless-rated tyre, and check the sidewall marking before mounting.

Use and maintenance

How do I set up my new wheels tubeless?

Fit the supplied tape and valve, mount an ETRTO-rated tubeless tyre, add 30–60 ml of sealant, then inflate in one burst to seat the bead and listen for the pops. Shake, check for leaks at the bead and valve, and set your riding pressure. The tubeless versus clincher comparison covers the failures people hit.

Are tubeless tyres really better?

They run at lower pressure with fewer pinch flats, and sealant closes most small punctures without a stop. The trade-offs: sealant needs refreshing every few months, a large sidewall cut can mean a plug or a tube, and hookless rims limit you to hookless-rated tyres and 72.5 PSI.

How often should I service the hubs?

Grease top-up around every 5,000 km, and check the ratchet at the same time. Wet, gritty or high-mileage riding shortens that — do it at the start of each season. DT 350 and 240 hubs need only standard tools, and the ratchet is a consumable, not a wear-out item.

Can a carbon rim be trued after a knock?

Small lateral deviations can be corrected by spoke tension adjustment, as with any wheel. A rim that has taken a hard impact and shows a crack, a soft spot or a change in spoke tension needs inspection before it is ridden — carbon does not bend back the way alloy does.

How should I clean carbon wheels?

Warm water, mild soap and a soft brush. Avoid solvents, degreasers on the rim surface and high-pressure washing, which drives water past the seals. For brake tracks, wipe with a clean cloth and inspect for glazing; never scrape the track.

Can scratches or cracks be repaired?

Cosmetic scuffs in the clear coat can be left alone or lightly polished. Cracks, delamination or a crushed bead hook cannot be repaired safely and need replacement — send photos to info@bola-bicycle.com and we will assess against the warranty and crash policy.

Which brake pads should I use on rim-brake wheels?

Use pads specified for carbon rims — a cork or carbon-specific compound. Standard alloy-rim pads overheat the track and can glaze or squeal. Keep pads clean, replace them before they wear through, and bed them in gently on the first descents.

Do carbon brake tracks overheat on long descents?

A carbon track runs cooler than an alloy rim under sustained braking and holds its performance better, but it is not immune. On long alpine descents, brake in short firm applications rather than dragging, and give the track a chance to cool between corners.

How do I mount tubular tyres?

Clean the rim bed, apply an even layer of tubular cement to both rim and tyre, let it tack, then mount and centre the tyre. Run 80–90 PSI for a 70 kg rider and 100–110 PSI for a 90 kg rider, and carry a spare tubular — a glued tyre is not a roadside tube change.

Can I use these wheels on a turbo trainer?

Yes on a direct-drive trainer, where the frame holds the bike and nothing loads the rim. Avoid roller trainers with rim-brake wheels — the brake track heats up with no airflow. Use a dedicated trainer tyre or wheel if you ride indoors through the winter.

How long do carbon wheels last?

Years, not seasons, when the hubs are serviced and the rims are not abused. The rim is the long-life part; bearings and ratchets wear first, and brake tracks on rim-brake wheels wear with use. Our warranty covers 36 months on rims and 24 months on wheelset assembly.

How should I pack them for travel?

Use a wheel bag with axle protectors, remove the cassette and rotors if the bag is tight, and keep spare spokes and the valve extender with the wheels. For flights, a hard case is worth it — the failure mode in soft bags is a crushed bead, which is not repairable.

How does a tubeless tyre actually seal?

The tyre bead locks against the rim seat and air pressure holds it there; sealant coats the inner casing and closes small cuts as they open. That is why a tubeless tyre must be seated properly before you ride — an unseated bead will not hold pressure, sealant or not.

Shipping, returns and warranty

How long does shipping take?

In-stock orders dispatch within 1–3 working days. Standard shipping then takes 7–20 working days and express 3–7. Out-of-stock or custom builds take about 15–25 days before dispatch, depending on order volume. Full detail is in the shipping policy.

Do I pay customs duty or VAT?

Economy shipping to the EU and the USA is DDP — duties and VAT are prepaid by us, so nothing is collected at the door. For other countries, and for express shipping to the EU or USA, the buyer covers duties, import tax and clearance fees. Free shipping never includes remote-area surcharges or destination handling.

What is the return window?

14 days from delivery to request a return, with the item unused, in its original packaging and with proof of purchase. Email info@bola-bicycle.com first — returns sent without a request are refused. Return shipping is paid by the customer, and some item types are excluded.

What does the warranty cover?

36 months on carbon rims and 24 months on complete wheelset assembly, from the shipping date, against manufacturing defects — delamination, non-impact structural cracking and resin voids. Branded hubs and spokes follow their manufacturer's term. The first 60 days include the replacement part and shipping; after that the customer covers international shipping and duties.

What is the crash replacement programme?

Within 12 months of purchase, a wheel damaged in a crash or an impact can be replaced at 30% off rather than full price. The customer covers freight, import taxes and component transfer. It sits alongside the standard warranty, not instead of it.

How do I make a warranty claim?

Email info@bola-bicycle.com with your order number, a description of the failure and photos of the damage. Our after-sales team assesses it directly; you do not go through the dealer you bought from.

Do I have to ship the defective part back?

No. Claims are handled from photos and the order record, and you keep the damaged part. That is deliberate — return freight on a wheel costs more than most replacements and delays the fix.

How do I track my order?

A tracking number is issued for every shipment. If tracking stalls for more than a week, email us with the order number; customs inspection and peak-season backlogs are the usual causes, and we chase the carrier rather than ask you to.

What happens if a parcel is lost or damaged in transit?

We reship or refund once the carrier claim is verified — you do not carry the loss. Send photos of the packaging and the damage as soon as it arrives, before you ride the wheels.

Can I change my address after ordering?

Yes if the order has not shipped — email us immediately with the order number. Once dispatched, the address is locked with the carrier. Check the address, phone and postcode before paying; delivery failures caused by wrong details are not covered.

Brand and OEM

Who is Bola, and where are the wheels made?

Bola is a carbon wheel and component brand based in Xiamen, Fujian, China, making its own rims and complete wheels rather than rebadging another factory's product. Company details are on the legal notice page.

Are you a factory or a reseller?

A factory with its own brand. The same rim line supplies our retail wheels and OEM customers, which is why custom drilling, layup and finish options are available — they are production changes, not special orders.

What is the difference between OEM and ODM?

OEM builds from your proven drawings — you own the design, we manufacture to it. ODM takes you from concept through engineering, tooling and production when the design still needs development. Most first-time buyers start with ODM and move to OEM once the design is fixed.

Is there a minimum order quantity?

Carbon tooling favours volume. Runs under roughly 50 units need engineering input to make the tooling economics work before a quote is issued. Ask early — the answer depends on the part and the mould it needs.

Which carbon grades can I specify?

T300 for cost-sensitive parts, T700 and T800 for the stiffness-to-weight sweet spot, and T1000 for the lightest, highest-spec builds. The grade is chosen against your load case, not as an upgrade for its own sake.

Can you manufacture from my drawings?

Yes — custom carbon parts from 2D drawings or 3D CAD, including brackets, fairings, seatposts, bars and forks, engineered to your loads and finish. Send the CAD and the load case, and we come back with a layup and a quote.

What resin, layup and finish options are there?

Epoxy or prepreg resin, a 0/45/90 layup tuned to your load case, and matte, gloss or raw finish. For frames and forks we recommend prepreg for consistent fibre volume; for low-volume brackets, epoxy wet layup is usually cheaper.

How long does an OEM project take?

It depends on whether tooling exists. An existing mould with a new drilling or finish runs in weeks; a new mould adds tooling and a sample-approval stage before production. We quote the timeline with the drawings rather than promise a number up front.