Carbon Wheels for Fixed Gear and Track Racing | 2027
Carbon Wheels for Fixed Gear & Track Racing in 2027 - The Best Carbon Wheelsets for Velodrome, Keirin, and Fixed Gear Street Riding
Short answer: Track and fixed-gear wheels use 100–120 psi, 23–28 mm tires, and 24–32 spokes, with no brake track and 120–144 mm rear spacing. A 50–60 mm front is standard for mass-start track; choose tubular or tubeless-ready rims rated for the higher pressure and check gear rules before racing.
What Makes a Good Track / Fixed Gear Wheelset?
1. Stiffness (Most Important for Track Racing)
- Why stiffness matters: Track racing involves massive power outputs - sprinters can hit 1,500-2,000W during standing starts, and even endurance riders push 400-600W continuously. A stiff wheel transfers power efficiently (no flex = more power to the ground) and handles predictably in tight velodrome banking.
- What makes a stiff wheel:
- Rim stiffness: A deep, wide carbon rim (50-80mm) is stiffer than a shallow, narrow rim. The rim's cross-sectional shape (box section vs. aero) also affects stiffness.
- Spoke count: More spokes = stiffer wheel. 24/24 is standard for track; 28/28 is stiffer (for heavy sprinters); 20/24 is lighter but less stiff (for endurance/pursuit).
- Spoke lacing: 2X or 3X lacing is stiffer than radial (radial is only for front wheels, and only for low-torque applications). For fixed gear (constant torque on both acceleration and deceleration), 2X/3X is essential.
- Hub flange width: A wider hub flange (wider spacing between flanges) creates a stiffer wheel (more lateral bracing angle). Track hubs often have wider flanges than road hubs.
- Spoke tension: Higher tension = stiffer wheel (up to the rim's strength limit). Track wheels are often tensioned higher than road wheels (130-150 kgf drive side, vs. 110-130 kgf for road).
2. Aerodynamics (Important for Velodrome)
- Why aero matters: On a velodrome, you're riding at 40-60 km/h (endurance) to 60-75 km/h (sprint). At these speeds, aerodynamic drag is the #1 resistance factor (more than rolling resistance or gravity). A more aero wheel saves watts - and watts matter in track racing (races are often decided by centimeters).
- What makes an aero wheel:
- Rim depth: Deeper = more aero (up to a point - 80-90mm is the sweet spot for track; disc wheels are even more aero for the rear).
- Rim shape: Wide, blunt, U-shaped rims are more aero than narrow, V-shaped rims (modern aero design).
- Spokes: Fewer spokes = more aero (less drag from spokes). Aero bladed spokes (Sapim CX-Ray) are more aero than round spokes. Carbon spokes are even more aero (wider, smoother, no spoke holes in the rim bed).
- Spoke count: 20/24 is more aero than 24/24 (fewer spokes = less drag). 16/20 is even more aero (for pursuit/endurance), but less stiff.
- Tire: A narrow, smooth tire (23-25c) is more aero than a wide, knobby tire. Track tires are typically 23-25c (tubular or clincher).
3. Hub Compatibility (Track-Specific)
- Track hubs vs. road hubs:
- Track hubs: Have a fixed cog on one side (and often a freewheel on the other - "flip-flop" hub), use a lockring to secure the cog, have wider flange spacing (for stiffer wheels), and often use solid axles (not quick release) for track use.
- Road hubs: Have a freehub body (for cassettes), use quick release or thru-axles, and have narrower flange spacing.
- Can you use road wheels on a track?
- Yes, with caveats: You can use a road wheelset on a velodrome if:1. The hub can accept a track cog (some road hubs can be converted, but most can't - you'd need a single-speed conversion kit or a track-specific hub).2. The wheel has a lockring (to prevent the cog from unscrewing during backpedaling - essential for fixed gear).3. The wheel is stiff enough (road wheels are often less stiff than track wheels, which can be a problem for sprinters).
- Better option: Use a track-specific wheelset (or convert a road wheelset with a track hub). Bola doesn't currently offer a dedicated track wheelset, but our road wheels can be adapted for fixed gear street riding (not competitive track racing) with a single-speed conversion.
4. Durability (Important for Fixed Gear Street)
- Fixed gear street riding is hard on wheels:
- Skidding: Fixed gear riders often skid to slow down (especially on the street). Skidding puts massive stress on the rear wheel - the tire wears out quickly (a tire can last 1-3 months of regular skidding), and the rear wheel experiences constant torque (both acceleration and deceleration).
- Bunny hops/curbs: Street riders often hop curbs, stairs, and obstacles - this puts impact stress on the wheels.
- Rough roads: Street riding involves potholes, debris, and rough surfaces - wheels need to be durable.
- What makes a durable fixed gear wheel:
- Rim material: Full T800 carbon is strong, but aluminum is more durable for street riding (aluminum dents but doesn't crack; carbon can crack from hard impacts). For competitive track racing, carbon is better (stiffer, lighter, more aero). For street fixed gear, aluminum may be more practical (cheaper to replace, more durable).
- Spoke count: 24/24 or 28/28 is more durable (more spokes = better load distribution, easier to replace a broken spoke).
- Spokes: Butted steel spokes (Pillar 1420/1423, Sapim CX-Ray) are strong and durable. Carbon spokes are lighter but less impact-resistant (not ideal for street riding).
- Hubs: Reliable, easy-to-service hubs (Bola 54T, DT Swiss 350) with good seals (for street riding in wet/dirty conditions).
- Tire: A durable, puncture-resistant tire (e.g., Continental Gatorskin, Schwalbe Durano) for street riding. For track, a smooth, fast-rolling tire (e.g., Continental Tempo, Vittoria Pista).
5. Weight (Less Important for Track, More for Street)
- Track racing: Weight is less important than stiffness and aero (on a velodrome, you're not climbing, and the constant speed means rotational weight matters less than aero). A 1,500g track wheelset is fine; a 1,300g wheelset is a bonus.
- Fixed gear street: Weight matters more (you're carrying the bike up stairs, hopping curbs, riding in stop-and-go traffic). A lighter wheel (1,400-1,500g) makes the bike easier to maneuver. But durability matters more than weight for street use.
Bola Models for Fixed Gear / Track Use
Important Note: Bola Doesn't Offer a Dedicated Track Wheelset
- Bola's current lineup is focused on road, gravel, triathlon, and MTB wheels - we don't currently offer a dedicated track/fixed gear wheelset (with a track-specific flip-flop hub, solid axle, and track cog/lockring).
- However, Bola road wheels can be adapted for fixed gear street riding (not competitive track racing) with a single-speed conversion. Here's how:
- Single-speed conversion: Remove the cassette from the freehub body, install a single-speed cog (e.g., Surly Single Speed Cog, 16-18T) with spacers, and secure with a lockring. This converts the road wheel to a single-speed (freewheel) - but NOT a fixed gear (the wheel still freewheels when you stop pedaling).
- Fixed gear conversion: To convert to true fixed gear, you'd need a track-specific hub (with a fixed cog and lockring on both sides, or a flip-flop hub). Most road hubs can't be converted to fixed gear (the freehub body is designed for cassettes, not fixed cogs). You'd need to rebuild the wheel with a track hub (e.g., Phil Wood Track Hub, White Industries ENO Track Hub).
- Recommendation for competitive track racing: Buy a dedicated track wheelset (e.g., Mavic Ellipse, Shimano Dura-Ace Track, Zipp 808 Track) - these are designed specifically for track use (stiff, aero, track-compatible hubs). Bola road wheels are not ideal for competitive track racing.
- Recommendation for fixed gear street riding: Bola road wheels can work for casual fixed gear street riding (with a single-speed conversion), but for serious fixed gear (skidding, tricks, heavy use), an aluminum wheelset with a track hub is more durable and practical.
Best for Casual Fixed Gear Street: Bola ULT (Mid tier) with Single-Speed Conversion
- Specs: Full T800, Bola 54T + TPI Ceramic, Sapim CX-Ray, 24/24, ~1,380-1,480g
- Why it works for casual fixed gear street:
- Stiff: Full T800 rim + Sapim CX-Ray spokes + 24/24 lacing = stiff enough for casual fixed gear riding (acceleration, cornering, light skidding).
- Durable: T800 carbon is strong, and Sapim CX-Ray spokes are durable. For casual street riding (not heavy skidding or tricks), this is fine.
- Light: ~1,380-1,480g - light enough for carrying up stairs and maneuvering in traffic.
- Reliable hub: Bola 54T is reliable and easy to service - good for street riding (wet/dirty conditions).
- Limitations:
- Not true fixed gear: With a single-speed conversion, the wheel freewheels (not fixed). You can't skid-stop (the wheel will just coast). For true fixed gear, you'd need a track hub rebuild.
- Not for heavy skidding: Carbon rims are not designed for skidding (the constant friction and heat can damage the rim's sidewall and clear coat). If you skid regularly, use an aluminum wheelset.
- Freehub body wear: Single-speed cogs can wear the freehub body's splines over time (especially with hard pedaling). Use a cog with a wide base (e.g., Surly) to minimize wear.
- Setup: 38mm or 45mm depth (38mm = lighter, more maneuverable; 45mm = stiffer, more aero), 21mm or 24mm internal width (21mm = for 25-28c street tires; 24mm = for 28-32c comfortable tires), single-speed conversion (16-18T cog, depending on your gear ratio preference), durable street tire (e.g., Continental Gatorskin, Schwalbe Durano).
Best for Budget Fixed Gear Street: Bola CLA (Entry tier) with Single-Speed Conversion
- Specs: T700/T800 mix, Bola 54T + Enduro Steel, Pillar 1423, 24/24, ~1,550-1,650g
- Why it works for budget fixed gear street:
- Cheapest Bola option: Entry tier - if you're going to use a carbon wheel for street fixed gear (with the risk of damage from skidding/curbs), you don't want to use your expensive ULT/SL/EXP wheels. The CLA is affordable enough for street use.
- Durable: T700/T800 mix is strong, and Pillar 1423 spokes are durable.
- Reliable hub: Bola 54T is reliable and easy to service.
- Limitations: Same as ULT (not true fixed gear, not for heavy skidding, freehub wear), plus heavier (~1,550-1,650g) and steel bearings (not ceramic).
- Setup: 38mm depth, 21mm internal width, single-speed conversion, durable street tire.
Best for Track Racing (Recommendation): Buy a Dedicated Track Wheelset
- Why Bola road wheels aren't ideal for track racing:
- No track hub: Bola road hubs use freehub bodies (for cassettes), not track cogs/lockrings. You can't easily convert to fixed gear.
- Less stiff: Bola road wheels are designed for road riding (balance of stiffness, weight, comfort) - they're less stiff than dedicated track wheels (which prioritize stiffness for sprinting and standing starts).
- No disc wheel option: Track racing often uses a rear disc wheel (for maximum aero). Bola doesn't offer a disc wheel.
- No tubular option: Track racing often uses tubular tires (for lower rolling resistance and the ability to run at very high pressure). Bola wheels are clincher/tubeless (not tubular).
- Recommended track wheelsets (if you want to compete):
- Budget: Mavic Ellipse (~Entry tier) - aluminum, track-specific, durable.
- Mid-range: Shimano Dura-Ace Track WH-7710 (~Mid–Premium tier) - carbon/aluminum, track-specific, stiff.
- High-end: Zipp 808 Track (~Premium tier) - carbon, aero, track-specific.
- Disc wheel: Zipp Super-9 Track Disc (~Premium tier) - rear disc for maximum aero.
- If you want to try track racing casually: You can ride on a velodrome with a road bike (with a single-speed conversion) - most velodromes allow road bikes for beginner sessions. But for competitive racing, you'll need a dedicated track bike/wheelset.
Fixed Gear / Track Setup Tips
Gear Ratio
- Track racing: Gear ratios depend on the event:
- Sprint: 48x15 (84 gear inches) to 52x14 (99 gear inches) - high gear for top speed.
- Keirin: 47x15 (82 gear inches) to 49x15 (86 gear inches) - similar to sprint.
- Pursuit/endurance: 48x16 (81 gear inches) to 50x16 (84 gear inches) - slightly lower for sustained effort.
- Points/scratch race: 46x15 (80 gear inches) to 48x15 (84 gear inches) - versatile for changing pace.
- Fixed gear street: Gear ratios depend on terrain and preference:
- Flat city: 46x16 (76 gear inches) to 48x16 (80 gear inches) - easy to accelerate, manageable for skidding.
- Hilly city: 42x16 (70 gear inches) to 44x16 (73 gear inches) - lower for climbing.
- High-speed street: 48x15 (84 gear inches) to 50x15 (88 gear inches) - high for top speed, harder to skid.
- Gear inch formula: Gear inches = (chainring teeth / cog teeth) x wheel diameter (inches). For a 700c wheel with a 23c tire, wheel diameter ≥27 inches. So 48x16 = (48/16) x 27 = 81 gear inches.
Tire & Pressure
- Track racing:
- Tire type: Tubular (glued to the rim) is standard for track racing (lower rolling resistance, can run at very high pressure, no risk of pinch flats). Clincher/tubeless is allowed in some events but less common.
- Tire width: 23-25c is standard (narrow = more aero, lower rolling resistance on smooth velodrome surface).
- Tire pressure: 120-160 psi (tubular) - high pressure for low rolling resistance on the smooth velodrome. Check the tire's maximum pressure rating.
- Tire choice: Continental Tempo/Tempo II, Vittoria Pista/Pista Control, Challenge Pista Record.
- Fixed gear street:
- Tire type: Clincher (with inner tube) or tubeless - easier to repair/replace than tubular. Tubeless is becoming popular (fewer flats, lower pressure).
- Tire width: 25-32c - wider = more comfort, better grip, more puncture resistance on rough streets. 28c is a good all-around choice.
- Tire pressure: 70-100 psi (clincher) or 60-80 psi (tubeless) - lower pressure for comfort and grip on rough streets. Adjust based on your weight and tire width.
- Tire choice: Continental Gatorskin (durable, puncture-resistant), Schwalbe Durano (fast, durable), Specialized Armadillo (puncture-resistant), Panaracer GravelKing (versatile, comfortable).
Skidding & Brake Setup
- Fixed gear street: Most fixed gear street riders use a front brake (for reliable stopping) and skid the rear wheel (for slowing down/style). Some riders ride brakeless (relying solely on skidding and backpedaling) - this is not recommended for safety (you can't stop quickly in an emergency).
- Skidding technique: To skid, shift your weight forward (off the saddle), lock your legs (stiffen both legs), and apply backward pressure on the pedals (resist the pedals' forward rotation). The rear wheel will lock up and skid. Practice on a smooth, empty surface before skidding in traffic.
- Tire wear from skidding: Skidding wears out the rear tire quickly (a tire can last 1-3 months of regular skidding). Use a durable tire (e.g., Continental Gatorskin) and rotate the tire occasionally (to even out wear).
- Carbon rim warning: Skidding on a carbon rim (with a clincher/tubeless tire) generates heat at the tire/rim interface. This heat can:
- Soften the tubeless tape (causing air leaks).
- Dry out the tubeless sealant (reducing puncture protection).
- Damage the rim's clear coat (causing discoloration or peeling).
- In extreme cases, cause the tire to blow off the rim (from heat-induced pressure increase).
- Recommendation: If you skid regularly, use an aluminum wheelset (not carbon). Aluminum rims dissipate heat better and are cheaper to replace. If you must use carbon, use a clincher (with inner tube) rather than tubeless (less risk of tape/sealant damage), and monitor the rim temperature (stop if the rim feels too hot to touch).
Velodrome Etiquette & Safety
- Track rules: Velodromes have strict rules for safety:
- Ride the line: Stay on the sprinter's line (the black line near the bottom of the track) unless passing. Pass on the outside (above the sprinter's line).
- No sudden moves: Don't swerve, slow down suddenly, or move down the track without checking behind you.
- Hold your line: When riding in a group (paceline), hold a steady line - don't overlap wheels (the rider in front can't see you, and a sudden move can cause a crash).
- No brakes on the track: Most velodromes require track bikes (fixed gear, no brakes) for competitive sessions. Road bikes with brakes are often allowed for beginner sessions but not for racing.
- Wear a helmet: Always wear a certified helmet on the velodrome.
- Etiquette:
- Call your moves: If you're passing, call "stick" (passing on the inside) or "high" (passing on the outside).
- Don't half-wheel: Don't ride with your front wheel alongside the rider in front's rear wheel (half-wheeling) - it's dangerous and annoying.
- Be predictable: Ride a steady line, maintain consistent speed, and signal your intentions (slowing, moving up/down the track).
- Respect faster riders: If you're riding slower, stay on the sprinter's line (or below it) and let faster riders pass on the outside. Don't impede faster riders.
- Warm up properly: Spend 10-15 minutes warming up (easy riding, leg openers) before going hard. Cold muscles = higher injury risk.
What Are the Frequently Asked Questions?
Q: I want to get into track racing at my local velodrome. I currently ride a Bola ULT wheelset on my road bike. Can I use these wheels on the track, or do I need to buy a separate track wheelset? What's the minimum gear I need to start track racing?A: Great question - track racing is a fantastic sport (fast, tactical, community-oriented), and getting started doesn't require a huge investment. Here's my detailed recommendation:
1. Can you use your Bola ULT road wheels on the velodrome?- For beginner/intro sessions: Yes - most velodromes allow road bikes (with brakes) for beginner sessions, intro classes, and open track time. Your Bola ULT wheelset will work fine for these sessions - you'll just need to:- Remove the derailleur and cassette (or convert to single-speed): Most velodromes require a single-speed drivetrain (no derailleur) for track riding, even for beginners. You can convert your road wheel to single-speed by removing the cassette, installing a single-speed cog (e.g., Surly Single Speed Cog, 16-18T) with spacers, and securing with a lockring. You'll also need to remove or disable the front/rear derailleurs (or use a chain tensioner if you keep the front derailleur).- Check the velodrome's rules: Some velodromes require track bikes (fixed gear, no brakes) for all sessions; others allow road bikes (with brakes) for beginners. Check your local velodrome's website or call them to confirm. Most velodromes offer "beginner track nights" where road bikes are allowed.- Use a lower gear: For your first track sessions, use a lower gear (e.g., 42x16 = 71 gear inches, or 44x16 = 74 gear inches) - this makes it easier to control speed and learn the track. You can increase the gear as you gain experience.- For competitive racing: No - once you start racing (not just open track sessions), you'll need a dedicated track bike/wheelset. Here's why:- Fixed gear requirement: Most track races require a fixed gear drivetrain (no freewheel). Your Bola ULT road wheel has a freehub body (for cassettes) - it can't be converted to fixed gear (the freehub body is designed for cassettes, not fixed cogs/lockrings). You'd need to rebuild the wheel with a track hub (e.g., Phil Wood, White Industries ENO) - which costs Entry tier for the hub + rebuilding labor. At that point, it's cheaper to buy a dedicated track wheelset.- Stiffness: Track racing (especially sprinting and standing starts) puts massive torque on the rear wheel. Your Bola ULT (24/24 spokes, road hub) is stiff enough for road riding, but not as stiff as a dedicated track wheel (which often has 28/32 spokes, wider hub flanges, and higher tension). For endurance/pursuit racing, the ULT's stiffness is probably fine, but for sprinting, you'd want a stiffer wheel.- Aero: Track racing happens at 40-75 km/h - aero matters. Your Bola ULT (38-50mm rim) is reasonably aero, but dedicated track wheels often have deeper rims (60-90mm) or disc wheels (rear) for maximum aero. For endurance racing, the ULT's aero is fine; for sprinting/pursuit, you'd want a deeper/disc wheel.- Tubular: Most track racing uses tubular tires (glued to the rim) - lower rolling resistance, can run at very high pressure (120-160 psi), no risk of pinch flats. Your Bola ULT is clincher/tubeless - it works, but tubular is faster (and standard for competitive track racing).- No brakes: Track racing requires no brakes (fixed gear only). Your road bike has brakes - you'd need to remove them (or buy a track bike without brakes).- Bottom line: Use your Bola ULT for beginner/intro sessions (with a single-speed conversion), but invest in a dedicated track bike/wheelset if you decide to race competitively.
2. What's the minimum gear you need to start track racing?- Level 1: Try it out (beginner sessions) - Entry tier additional (use what you have):- Bike: Your road bike (with Bola ULT wheels) - convert to single-speed (remove cassette, install single-speed cog + spacers + lockring, remove/disable derailleurs).- Helmet: Any certified road helmet (you probably already have one).- Clothing: Road cycling kit (jersey, bibs, shoes) - you probably already have this.- Cost: Entry tier (single-speed cog + spacers + lockring, if you don't already have them).- What you can do: Beginner track classes, open track sessions, group rides at the velodrome. This is enough to learn the basics (track etiquette, lines, pacing) and decide if you want to continue.- Level 2: Casual racing (weekly races) - Mid–Premium tier:- Track bike: You'll need a dedicated track bike (fixed gear, no brakes, track geometry). You can buy:- Used: Entry–Mid tier (e.g., used Fuji Track, Specialized Langster, Trek T1) - check eBay, Facebook Marketplace, or your local velodrome's classifieds.- New entry-level: Mid–Premium tier (e.g., Fuji Track Elite, Specialized Langster Pro, State Undefeated) - aluminum frame, carbon fork, entry-level track wheels.- Track wheelset: Most entry-level track bikes come with decent aluminum track wheels (e.g., Mavic Ellipse, Shimano RS). For casual racing, these are fine. If you want to upgrade, a carbon track wheelset costs Mid–Premium tier (e.g., Zipp 808 Track, Reynolds Strike Track).- Track tires: higher per tire (tubular or clincher). For casual racing, clincher track tires (e.g., Continental Tempo, Vittoria Pista) are fine - easier to install/replace than tubular.- Helmet: Any certified road helmet (you can use your road helmet). Some track racers use aero helmets (for pursuit/endurance), but they're not required for casual racing.- Shoes: Road cycling shoes work fine (you can use your road shoes). Track-specific shoes are available (stiffer soles, ventilation), but not required.- Cost: Mid–Premium tier (for a used/new entry-level track bike + tires + accessories).- What you can do: Weekly track races (scratch, points, pursuit), state championships, regional races. This is enough for competitive racing at the amateur level.- Level 3: Serious racing (national/international) - Premium tier+:- Track bike: High-end track bike (carbon frame, aero geometry) - Premium tier (e.g., Specialized S-Works Tarmac Track, Trek Madone Track, Felt TK1).- Track wheelset: High-end carbon track wheelset - Premium tier (e.g., Zipp 808 Track, Enve 7.8 Track, Reynolds Strike Track). For sprinting/pursuit, add a rear disc wheel - Premium tier (e.g., Zipp Super-9, Discwheel).- Track tires: High-end tubular track tires - higher per tire (e.g., Continental Tempo II, Vittoria Pista Control, Challenge Pista Record). You'll need multiple sets (for different events/conditions).- Aero helmet: Entry tier (e.g., Giro Aerohead, LW P5) - for pursuit/endurance racing.- Aero clothing: Entry–Mid tier (aero skinsuit, aero shoe covers, aero gloves) - for competitive racing.- Power meter: Mid–Premium tier (e.g., SRM, Power2Max, 4iiii) - for training and pacing.- Cost: Premium tier+ (for a high-end track bike + wheelset + tires + aero gear + power meter).- What you can do: National championships, international races (UCI events), Masters World Championships. This is the gear used by serious track racers.
3. My recommendation for getting started:- Step 1: Try a beginner session - Contact your local velodrome and sign up for a "beginner track class" or "intro to track racing" session. These usually cost Entry tier and include bike rental (if you don't have a suitable bike). This is the best way to try track racing without investing any money.- Step 2: Use your road bike (Bola ULT) for open sessions - If you enjoy the beginner session, convert your road bike to single-speed and start attending open track sessions. Practice your lines, pacing, and track etiquette. This costs Entry tier (single-speed cog + spacers + lockring).- Step 3: Buy a used entry-level track bike - If you decide to race competitively, buy a used entry-level track bike (Entry–Mid tier) with aluminum track wheels. This is enough for weekly races and state championships. You can keep your Bola ULT wheels for road riding (don't use them on the track for racing - they're not ideal, and you risk damaging them).- Step 4: Upgrade as you progress - As you get faster and more competitive, upgrade your wheelset (carbon track wheels, Mid–Premium tier), tires (tubular, Entry tier each), and eventually your frame (carbon track frame, Premium tier). But don't upgrade too early - focus on fitness and technique first (the rider matters more than the gear, especially at the amateur level).
4. Tips for your first track session:- Arrive early: Get to the velodrome 30-60 minutes early - you'll need time to set up your bike, warm up, and learn the track rules.- Ask questions: The track community is friendly and welcoming - don't be afraid to ask experienced riders for advice (lines, gearing, etiquette). Most riders are happy to help beginners.- Start slow: Don't try to go fast on your first session - focus on learning the track (lines, banking, pacing) and riding smoothly. Speed will come with experience.- Use a lower gear: For your first session, use a lower gear (e.g., 42x16 = 71 gear inches) - this makes it easier to control speed and learn the track. You can increase the gear as you gain experience.- Hold your line: The #1 rule of track riding is "hold your line" - don't swerve, don't slow down suddenly, and don't move up/down the track without checking behind you. Predictable riding = safe riding.- Have fun: Track racing is challenging but fun - embrace the speed, the tactics, and the community. Don't worry about being fast on your first day - everyone starts as a beginner.
5. Final answer:- For beginner/intro sessions: Yes, you can use your Bola ULT road wheels (with a single-speed conversion) - no additional cost.- For competitive racing: No, you'll need a dedicated track bike/wheelset - budget Mid–Premium tier for a used/new entry-level track bike with aluminum track wheels.- Minimum gear to start: A road bike (converted to single-speed) + helmet + cycling kit = Entry tier additional (use what you have). For racing, add a track bike = Mid–Premium tier
If you have more questions about track racing, gear, or getting started, contact your local velodrome (they're usually very helpful to beginners) or reach out to Bola at info@bolacarbon.com - we're happy to help you get started in track racing.
Ready to Explore Fixed Gear / Track Riding?
While Bola doesn't currently offer a dedicated track wheelset, our road wheelsets work great for casual fixed gear street riding (with a single-speed conversion) and for beginner velodrome sessions. Visit bolacarbon.com to explore our full lineup:
- Best for casual fixed gear street: Bola ULT (Mid tier) - T800, Sapim CX-Ray, TPI Ceramic, 54T
- Best for budget fixed gear street: Bola CLA (Entry tier) - T700/T800, Bola 54T, Pillar 1423
- Best for all-around road/track: Bola SL (Mid tier) - T800, DT Swiss 350s, Sapim CX-Ray
- Best for aero/track-style: Bola PRO (Mid tier) or EXT (Premium tier) - T800, carbon spokes, deep aero rims
All Bola wheels come with: 2-year warranty, crash replacement program, free worldwide shipping, tubeless tape/valves pre-installed, and responsive customer support (info@bolacarbon.com).
If you're interested in a dedicated Bola track wheelset (we're considering adding one to our lineup), let us know - we're always listening to rider feedback and expanding our product range based on demand.
Remember: Track racing is one of the most exciting forms of cycling - fast, tactical, and community-oriented. Whether you're riding fixed gear on the street or racing on the velodrome, the right wheelset makes all the difference. Start with what you have, learn the basics, and upgrade as you progress. See you on the track.
Ready to Upgrade Your Wheels?
Explore Bola's complete carbon wheel collection and find the perfect match for your riding style and budget:
- Bola ULT 45G Carbon Gravel Wheelset - Mid tier
- Bola SL 45G Carbon Gravel Wheelset (DT Swiss 350S) - Mid tier
- Bola ULT 50R Carbon Triathlon Wheelset - Mid tier
- Bola CLA 60/88 Triathlon Carbon Wheelset - Entry tier
- Gravel Wheels - full collection
- Triathlon & TT Wheels - full collection
- Road Wheels - full collection
All Bola wheelsets include: tubeless tape + valves, 2-year warranty, crash replacement program (50% off), and free worldwide shipping on qualifying orders Have questions about which wheelset is right for you? Contact our engineering team at info@bolacarbon.com.
Further reading: carbon road wheel buying guide: depth and width covers depth, width, hub and rim decisions in one place. Durability testing, wear limits and service intervals are covered in carbon wheel fatigue and impact testing.
Explore Next
Specifications and buying options:
Key Takeaways
- Fixed gear and track cycling put unique demands on wheels - you need a wheel that's stiff (for sprinting and standing st
- Q: I want to get into track racing at my local velodrome.
- Engineered for performance: Carbon Wheels for Fixed Gear and Track Racing in 2027 - The Best Carbon Wheelset.